Non-Sparking AlBr Combination Spanner 1/4 inch
-
non-sparking-albr-combination-spanner-1-4-inch-smea-1002a
Die forged
- These Spanners are used for tightening and loosening nuts in production or general service work
- These Spanners are used when it is difficult to access a bolt/nut with a socket or a Ring Spanner
- Select the tool size that fits the workpiece securely.
| P/N | S mm | L mm |
| SME-6 | 6 | 105 |
| SME-7 | 7 | 120 |
| SME-8 | 8 | 120 |
| SME-9 | 9 | 135 |
| SME-10 | 10 | 135 |
| SME-11 | 11 | 150 |
| SME-12 | 12 | 150 |
| SME-13 | 13 | 175 |
| SME-14 | 14 | 175 |
| SME-15 | 15 | 195 |
| SME-16 | 16 | 195 |
| SME-17 | 17 | 195 |
| SME-18 | 18 | 215 |
| SME-19 | 19 | 215 |
| SME-20 | 20 | 230 |
| SME-21 | 21 | 230 |
| SME-22 | 22 | 245 |
| SME-23 | 23 | 265 |
| SME-24 | 24 | 265 |
| SME-25 | 25 | 265 |
| SME-26 | 26 | 290 |
| SME-27 | 27 | 290 |
| SME-30 | 30 | 320 |
| SME-32 | 32 | 340 |
| SME-34 | 34 | 360 |
| SME-35 | 35 | 360 |
| SME-36 | 36 | 360 |
| P/N | S in | L mm |
| SMEA-1002 | 1/4″ | 105 |
| SMEA-1004 | 5/16″ | 120 |
| SMEA-1006 | 3/8″ | 135 |
| SMEA-1008 | 7/16″ | 150 |
| SMEA-1010 | 1/2″ | 175 |
| SMEA-1012 | 9/16″ | 175 |
| SMEA-1014 | 19/32″ | 195 |
| SMEA-1016 | 5/8″ | 195 |
| SMEA-1018 | 11/16″ | 195 |
| SMEA-1020 | 3/4″ | 215 |
| SMEA-1022 | 13/16″ | 230 |
| SMEA-1024 | 7/8″ | 245 |
| SMEA-1026 | 15/16″ | 265 |
| SMEA-1028 | 1″ | 290 |
| SMEA-1030 | 1-1/16″ | 290 |
| SMEA-1032 | 1-1/8″ | 320 |
| SMEA-1034 | 1-3/16″ | 320 |
| SMEA-1036 | 1-1/4″ | 340 |
| SMEA-1038 | 1-5/16″ | 360 |
| SMEA-1040 | 1-3/8″ | 360 |
PROPER USE
- These Spanners are used for tightening and loosening nuts in production or general service work
- These Spanners are used when it is difficult to access a bolt/nut with a socket or a Ring Spanner
- Select the tool size that fits the workpiece securely.
ABUSE/MISUSE
- Do not use this tool to open “Stubborn/Frozen” nuts or bolts.
- Never use an extension on the spanner handle. It will break the tool and can cause injury to the operator
- Never strike this Spanner with a hammer or any other tool
- Never Cock or Tilt and Open-Ended Spanner. The nut should be fully seated
- Do not apply load more than the designated torque
Guest July 10, 2025
Build quality is good and safe to operate.
Guest May 14, 2025
Safe to use and well finished.
Guest May 12, 2024
Tool meets industrial safety needs.